used TOSHIBA IS100G3Y year 1996' (SOLD)

used TOSHIBA IS100G3Y year 1996' with good running condition.

Pls contact

JadChoon +6017 365 1128

jadchoon@gmail.com

used SUMITOMO SH75NIVA 94' (SOLD)

used SUMITOMO SH75NIVA year 1994'

pls contact

JadChoon +6017 365 1128

jadchoon@gmail.com

used NIIGATA MM300MI 96' (SOLD)

used NIIGATA MM300MI year 1996'

pls contact:

JadChoon +6017 365 1128

jadchoon@gmail.com

used niigata (vertical)CND50VR 90' (SOLD)

used niigata (vertical) CND50VR year 1990'

pls contact

JadChoon +6017 365 1128

jadchoon@gmail.com

used KAWAGUCHI K265BX 89' (SOLD)

used KAWAGUCHI K265BX year 1989' with good running condition

pls contact:

JadChoon +6017 365 1128

jadchoon@gmail.com

used kawaguchi K125BX 89' (SOLD)

used kawaguchi K125BX year 1989' with good running condition.

pls contact

JadChoon +6017 365 1128

jadchoon@gmail.com

used JSW 850ton 95'

used JSW 850ton year1995' with good running condition.

Pls contact:

JadChoon +6017 365 1128

jadchoon@gmail.com

used Arburg 320M 94' (SOLD)

Used Arburg 320M year 1994'

Pls contact

JadChoon 0173651128

jadchoon@gmail.com

used KAWAGUCHI K265B year 88' (SOLD)

KAWAGUCHI K265B 88'

In good running condition.

Please contact JadChoon 017 365 1128/ Email: jadchoon@gmail.com

Used Toshiba IS550GSW year 98' (SOLD)

This used Toshiba plastic IMM is located in Japan with very good condition.

If interested, please contact:

Jad Choon +6017 365 1128 or email to : jadchoon@gmail.com

Used Toyo Si-450II year 03' (SOLD)

This used plastic IMM is located in Japan with very good condition.

If interested, please contact:

Jad Choon +6017 365 1128 or email to : jadchoon@gmail.com

Toshiba IS150EN year 88' clamping mould 170ton

This used plastic IMM (imported fr Japan) is located in Malaysia.

Please contact:

JadChoon +6017 365 1128

Toshiba IS150EN year 89'

This used IMM (imported fr Japan) is located in Malaysia.

Contact person: Jad Choon +6017 365 1128

used sumitomo SG150S year 94' (SOLD)

This used sumitomo SG150S (imported fr Japan) is located at Malaysia.

Contack person: Jad Choon +6017 365 1128

used Nissei PS40E5ASE year 93' (SOLD)

This used nissei 40ton plastic IMM (imported from Japan) is located in Malaysia. Contact us if interested.Thank you

contack person: Jad Choon +6017 365 1128

Toyo Si-850IV

Item			Si-850IV
	Injection unit type	-	L			M		N
	Screw diameter	mm	83	90	100	100	110	110	120
	Theoretical injection capacity	cm3	2272	2863	3534	3927	3752	4752	6220
I injection unit	Injection unit	-	L750B(※)			M750B		N1100B
	Max. injection speed	mm/s	170			150		150
	Max. injection pressure	MPa	215.6	186.2	151.9	186.2	151.9	171.5	143
	Clamping force	kN	8830
	Tie bar clearance (H×V)	mm	1320 X 1320

• ・The figures are subject to change without any legal obligation on the part of the manufacture.
• ・The specifications are expressed in SI units.（1MPa=10.2kgf/cm²、1kN=0.102tonf）
• ・The maximum injecting pressure is attainable maximum set values. This value may be limited by molding conditions and cycle time.
• ・The maximum injecting speed is calculated values. This value may be limited by set injecting pressures.
• ・A large-sized screw may not be applicable to some kinds of material.
• ※The heat barrel (φ83, high-pressure use) for the L750B injection unit is not compatible with that of the K600B.

Toyo Si-680IV

Item			Si-680IV
	Injection unit type	-	K			L			M
	Screw diameter	mm	68	75	83	83	90	100	100	110
	Theoretical injection capacity	cm3	1111	1656	2028	2272	2863	3534	3927	4752
I injection unit	Injection unit	-	K600B			L750B(※)			M750B
	Max. injection speed	mm/s	180			170(※)			150
	Max. injection pressure	MPa	215.6	176.4	147	215.6	186.2	151.9	186.2	151.9
	Clamping force	kN	6664
	Tie bar clearance (H×V)	mm	1145 X 1145

• ・The figures are subject to change without any legal obligation on the part of the manufacture.
• ・The specifications are expressed in SI units.（1MPa=10.2kgf/cm²、1kN=0.102tonf）
• ・The maximum injecting pressure is attainable maximum set values. This value may be limited by molding conditions and cycle time.
• ・The maximum injecting speed is calculated values. This value may be limited by set injecting pressures.
• ・A large-sized screw may not be applicable to some kinds of material.
• ※The heat barrel (φ83, high-pressure use) for the L750B injection unit is not compatible with that of the K600B.